How many sheets of plywood for a 12×12 roof?

Short answer

A 12 × 12 ft building with a 4/12 gable roof and 12 inch overhangs has about 207 square feet of roof to sheathe, and needs 8 sheets of 4 × 8 plywood or OSB with 10% waste — 7.1 sheets before rounding up.

How to work it out

  1. Slope factor at 4/12: √(1 + slope²) = 1.0541
  2. Along the ridge: 12 ft + 2 × 12 in = 14 ft · down each slope: (12 ft ÷ 2 + 12 in) × 1.0541 = 7.38 ft
  3. 2 slopes × 14 ft × 7.38 ft = 207 sq ft
  4. 207 sq ft × 1.1 waste ÷ 32 sq ft per sheet = 7.1 → 8 sheets

A roof covers more than the floor under it. The overhangs add a foot all round, and the slope stretches every foot of level run, so a 12 × 12 ft shed or garden building takes about 8 sheets on the roof against 5 on the floor.

The count changes with the pitch, so the table below runs it from a nearly flat 2/12 to a steep 12/12. Enter your own overhang if it is not 12 inches.

Adjust for your project

ft
ft
Outside of the wall plates. Shed roof: low wall to high wall.
in 12
Rise in inches for every 12 in of level run (6 = 6/12). A roofer’s pitch gauge or a level and tape will read it.
in
Eaves and gable ends. The sheathing runs out over them too. 0 if the roof stops at the walls.
More options: Openings · Waste · Price
sq ft
Windows, stair holes, skylights
%
$
Sheets to buy8 sheets4 × 8 ft
Full-sheet layout count (no offcut reuse)
8 sheets · 4 × 8 ft
Area to cover
207 sq ft
Roof area in roofing squares (100 sq ft each)
2.1
  • Subfloor and roof sheathing run with the long edge across the joists or rafters, and end joints must land on framing — on small or odd-shaped areas that can push waste above 10%.
  • Hips, valleys and dormers cut more sheets into angled pieces than a plain gable or shed roof; allow 15% or more for them. Sheathing thickness follows the span rating stamped on the panel and your local code.

Next: Framing under it? Count the wall studs or work out the rafters.

For this job · affiliate link
Circular saw (7¼ in)A circular saw run along a clamped straightedge breaks sheets down cleanly — score the cut line or use a fine blade to limit splintering.
View on Amazon (opens in a new tab)

Sheets for a 12 × 12 ft gable roof by pitch (12 in overhangs)

Sheets for a 12 × 12 ft gable roof by pitch (12 in overhangs)
Pitch (in 12)Area to coverSheets to buy
2 in 12199 sq ft7 sheets
4 in 12207 sq ft8 sheets
6 in 12219 sq ft8 sheets
8 in 12236 sq ft9 sheets
10 in 12255 sq ft9 sheets
12 in 12277 sq ft10 sheets

What to know about sheathing a 12x12 roof

With 12 inch overhangs, each of the two slopes is 14 ft along the ridge and 7 ft of level run, from the ridge out to the end of the eave. At 4/12 the slope factor is 1.054, so each slope measures about 14 × 7.38 ft and the two together come to about 207 square feet. Ten percent waste on top makes 7.1 sheets, so you buy 8.

  • Each slope takes four sheets. Laid with the long edge across the rafters, one row of 8 ft sheets plus a 6 ft piece covers the 14 ft length, and a second row covers the rest of the 7.38 ft slope. The offcuts from the first row start the second.
  • Overhangs matter more than pitch on a small roof. Drop the overhangs to zero and the same roof needs only 6 sheets; raise the pitch from 4/12 to 6/12 and it still needs 8. Go steeper, from about 8/12, and it climbs to 9 sheets or more.
  • Stagger and gap the sheets. End joints should land on rafters and be staggered from row to row, and panel makers usually call for a small gap at edges and ends so the sheets can swell without buckling. Follow the stamp and the maker’s instructions.
  • Clips between rafters. On wider rafter spacing, many roof panels need H-clips at the unsupported edges; the panel’s span rating says when.

The floor of the same building is How many sheets of plywood for a 12x12 floor. For the rafters, work out the length and birdsmouth on Rafter length for a 12 ft shed at 4/12, and for the walls under it, How many sheets to sheathe a 24 ft wall, 8 ft high shows the vertical-sheet layout.

What you’ll need

As an Amazon Associate we earn from qualifying purchases. Links to products are affiliate links — they cost you nothing extra and help keep these calculators free.

Frequently asked questions

How many sheets of plywood for a 12x12 roof with no overhang?

6 sheets of 4 × 8 at 4/12 with 10% waste — 152 sq ft of roof, about a quarter less than with 12 inch overhangs.

How many sheets of plywood for a 12x12 roof at 6/12 pitch?

8 sheets of 4 × 8 for 219 sq ft of roof with 12 inch overhangs and 10% waste (7.53 before rounding).

How many sheets of plywood for a 10x10 roof?

6 sheets of 4 × 8 for a 10 × 10 ft building at 4/12 with 12 inch overhangs: 152 sq ft of roof plus 10% waste.

How many sheets of plywood for a 12x16 shed roof?

10 sheets of 4 × 8 for a 12 ft wide, 16 ft long gable at 4/12 with 12 inch overhangs — 266 sq ft of roof with 10% waste added on top.

Sources